Install a Vanity Sink Family Handyman.Overview.Before.This is what the bathroom looked like before the makeover.Sinks and vanities get more use than any other fixture in your house.Its no wonder they can look tired and run down after five or 1.Fortunately, changing a vanity is relatively easy, and if you paint the walls at the same time, you can achieve a stunning transformation.How To Install Countertop Side Splash' title='How To Install Countertop Side Splash' />In this article, well show you how to remove your old vanity and install a new one.All you need are basic carpentry and plumbing skills and usually just one weekend.We wanted an elegant, fine furniture look for our bath, so we went with a special order multiple piece vanity and matching solid surface top from a local home center.You may decide to purchase a one piece cabinet with a matching top, which is a bit easier to install, but the basic how to will be the same.Just follow our photos and read the text for buying information and additional tips.New vanities 4 ft.The top can be anything from cultured marble with a molded bowl starting at 1.While some of these prices might knock your socks off, keep in mind youll be able to find something in between to fit your budget and taste.Our setup was about 1,2.Removing your old vanity may be the toughest part of the job.Photo 1 Shut off the water Shut off the water to your sink before you disconnect your faucet supply tubes.Look for shutoff valves under the sink and turn them off.If you dont have shutoff valves, shut off the water supply where it enters your house.Turn on the sink faucet to make sure the water is completely off.Photo 2 Disconnect the pipes.Unscrew the supply tube nuts.Loosen both slip nuts and remove the P trap.The curved pipe will be full of dirty water, so have a pan and a rag handy to wipe any spill.Stuff a moist rag into the waste pipe to block sewer odor until youre ready to reconnect the trap.Photo 3 Remove the backsplash.Chisel away the tile backsplash before removing the vanity top.If you have a plastic laminate backsplash, just cut the caulk seam with a utility knife where the backsplash meets the wall.Photo 4 Remove the top.Look for screws that fasten the top to the cabinet and remove them.Your vanity top may be glued instead of screwed to the cabinet.Use your long blade scraper to slice through any visible glue and then pry the top off the cabinet.You may need to wiggle it back and forth a bit to free it from the wall and the cabinet.Photo 5 Pull the top free from the vanity and try to lift it straight out to minimize damage to the surrounding walls and fixtures.Get some help it may be heavier than you think.P lastic laminate countertops are economical, durable, easy to clean, come in a wide variety of designs, and best of all are relatively simple to install yourself.How to Cut Countertops.If you replace a countertop in your kitchen or bathroom, you may need to cut the new countertop to fit the desired area.Laminate.Lets compare quartz vs granite to see which countertop is best for your remodeling project.IKEA Home furnishings, kitchens, appliances, sofas, beds, mattresses.How To Install Countertop Side Splash' title='How To Install Countertop Side Splash' />Photo 6 Remove the vanity.Unscrew the vanity from the wall.If you dont see screws, look for large nails and use a pry bar to remove them.While youre at it, mark the wall stud locations.Theyll come in handy later.The first thing to do, of course, is to shut off the water supply Photo 1.Next, disconnect the plumbing connections that supply water to the faucet and the waste trap below the sink.Both nuts on the trap unscrew counterclockwise.If you have shutoff valves under the vanity that supply the hot and cold water, be prepared for the possibility that they may leak even after youve turned them off clockwise.If theyve been there for 2.If this is the case, shut off the main water supply and then replace the shutoff valves.You can get replacements at any hardware store or home center.Instead of coming out through the wall as in our photos, sometimes your water supply comes up through the bottom of the vanity.In this case, youll have to shut off the main water supply and remove the shutoff valves so you can lift the old vanity away from the pipes.When you install your new vanity later, just cut matching holes in the bottom to make way for the pipes and then install new shutoff valves once the new vanity is in place.With the plumbing unhooked, see how your vanity top is fastened.If its a one piece cultured top or solid surface, stone like top, its probably secured with a bead of silicone caulk.You can usually pry it loose a bit and slip a keyhole saw between the vanity and top and cut away the adhesive.If you have a tiled top Photo 4, there could be nails driven from the top into the vanity underneath the tile.These will usually come free with a pry bar.If you have a plastic laminate top, it could be fastened to the vanity with screws or caulk.Look for screws along the top edge of the vanity and remove them with a screw gun.If it seems nearly impossible to get the top free from the old vanity, you may have to take the whole thing out in one piece.This makes the job tougher, but with some clever maneuvering, youll be able to pull it free.Fix up and paint your wall before you install the new vanity.Photo 7 Clean up the wall.Scrape away any glue or caulk left on the wall with a sharp scraper.Be careful not to tear the drywall paper beyond the repair area.Remove any loose bits of paper.Photo 8 Patch the wall.Patch any wall damage with successive coats of drywall compound.Use a lightweight setting type compound to speed up the process so youll be able to sand and paint earlier.After the patch is dry, sand it smooth and even with the adjoining wall surface.Photo 9 Prime and paint the wall.Prime the wall patch and then paint the wall.We primed the entire wall medium gray to prevent the light color from showing through our new dark color.While its not impossible to paint after you install your new vanity and top, its sure a lot easier to do it beforehand.First remove any caulk residue and then patch any wall damage Photos 7 and 8.You may need a couple of coats of drywall compound if you have deep repairs.Wait for the patch to dry completely and then sand it smooth with the surrounding wall.Next, you can spot prime the repaired areas and paint the entire wall.If youre applying a darker paint over a light color as we did, prime all the drywall with a medium gray primer first ask for this from your paint supplier so youll get good coverage with the new paint Photo 9.Lay out your vanity dimensions on the wall.Photo 1.Mark the wall.Mark the locations of the new cabinets on the wall.We shifted our new cabinet assembly layout 38 in.Photo 1. All Keys 21 04 2013 Tfile Me Forum more. Install the filler strip.Nail the filler strip to the side of the cabinet that meets the wall.Filler strips may be necessary to give your cabinet doors room to swing without rubbing against the wall.You may need to taper the filler strip for a tight fit.Also, build up the floor with wood strips nailed flush to the finished floor to help with leveling and make small positioning adjustments.If your finished flooring doesnt continue under the vanity, its best to lay out your vanity dimensions on the wall to help position it accurately.Measuring vanity cabinets can be tricky, especially if you have a multiple piece vanity like ours.Just measuring the backs of the cabinets wont do.If the cabinet has a face frame, the rear width of each cabinet is about 12 in.Keep this in mind when you add up the dimensions for multiple cabinets.We ordered a filler strip to install on the right side of our cabinet where it met the wall.We also allowed for this extra width when we ordered our vanity top.These strips are typically 3 in.Photo 1.This shifted the layout to the left just far enough to cover the edge of the old floor and meet our tile baseboard.Doing this also gave us a nice, comfortable overhang for the vanity top on the left side of the completed cabinet.Adding a 38 in.Remember, you can also hide small problems where the vanity meets the floor by adding a molding strip to the edge.Youll also notice in Photo 1.Building up the floor does two things It allows you to slide the vanity into position without its falling into the old recess, and it keeps it up slightly so you dont lose height an inch can make a difference to your lower back.Mark the stud layout before you fasten your vanity to the wall.Photo 1.Screw the frames together.Screw the cabinet frames together before screwing them to the walls.Flush the fronts, clamp them, drill a clearance and pilot hole, then drive a screw near the top, middle and bottom of the cabinets.Evenly space the cabinet sides and shim them near the back and screw them together near the back edge.Cut protruding shims flush after you screw the cabinets to the wall.Close up of screwing frames together.How to Replace a Bathroom Faucet how tos.Identify the Type of Faucet You Already Have.There are three main faucet types available today single hole, 4 triple hole, and 8 triple hole.In the single hole faucet, the center control typically not only serves as the spout but the mixing valve as well.In the triple holes faucets, the center device is usually just the spout with the mixing valves 4 or 8 from the center on each side respectively.Depending on your existing situation, the faucet may be installed to the countertop or the sink, so if you are replacing one or the other, you have the option to change faucet type.If not, purchase a new faucet to match the type you already have.The one exception would be that single hole faucets can typically be used in a 4 triple hole sink or countertop if they come with a blank base plate to cover the additional holes.No Tracks Found Trials Evolution Ninja .
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |